Wipe off infeed and outfeed rollers. Clean base table. Light waxing will help wood material pass through the planer. Evaluate blade sharpness condition. Replace as necessary. Gauge Calibration, check thickness gauge calibration and turret stop calibration. Check brushes for wear and replace as necessary.
NOTE: No tools are necessary to install a belt. The use of a screwdriver or other tool to pry or stretch a belt may cause damage to the pulleys and ultimately destroy the new belt. Remove the two hex screws from the top, right side of the planer. Remove the two, small cross head screws securing the side panels to the top of the planer. Lift the side panel up out of the slot in the base and remove the panel from the machine. Notice the grooves inside the belt.
Start the belt on the top pulley P with 3 grooves on the pulley, as shown in Figure Guide the belt between the lower pulley and the height adjustment screw Q , as shown in Figure With three grooves engaged on the large pulley, rotate the pulley clockwise. Keep pressure on the edge of the belt to keep the grooves engaged on the small pulley.
Continue pressure on the side of the belt and rotate the large pulley while hopping the belt further onto the pulleys, as shown in Figure All of the belt grooves should be engaged in the final position and the pulleys should rotate smoothly.
Reinstall the side cover and the screws. Do not overtighten the self-tapping screws. The depth adjustment scale on your planer is set at the factory. However, with extended use, the depth adjustment scale could show an incorrect measurement.
Plane a piece of wood, noting the measurement on the depth adjustment scale. Measure the finished thickness of the workpiece. If the thickness of the workpiece does not match the reading on the depth adjustment scale, loosen the two cross head screws R shown in Figure Adjust the pointer up or down until its reading matches the finished thickness of the workpiece.
Securely re-tighten the screws. After extended use, the table extensions might become slightly out of level.
To ensure that the tables are level, place a straight edge on the table extension. The straight edge should contact the edge of the table extension and the main table Fig. When leveling, press the edge of the table extensions down to remove any play. For best results, use a level long enough to contact the edges of both table extensions. If the table extensions are not level, loosen the jam nuts T and adjust the table extension support bolts S up or down Fig.
This is set at the factory to reduce unnecessary friction between the material. Keep the table clean and free from oil, grease and pitch. Treat the table with paste wax to help maintain its smooth finish.
Your planer is equipped with an 18 amp circuit breaker. If your planer becomes overloaded and stops operating, turn off the planer, let the unit sit for 2 minutes and press the reset button U before you resume working.
NOTE: Circuit breaker overload is often the result of dull knives. Change your knives on a regular basis to avoid tripping your breaker. Check your knives before re-setting the circuit breaker and continuing to plane. See the Troubleshooting Guide at the end of this section for more information. Inspect carbon brushes regularly. Keep brushes clean and sliding freely in their guides. Always replace a used brush in the same orientation in the holder as it was prior to its removal.
Carbon brushes have varying symbols stamped into their sides, and if the brushes are worn down to the line closest to the spring, they must be replaced. Remove the brush inspection cap V. Withdraw the brush assembly. Electric shock may result. It is recommended that, once a year, you take or send the tool to a D E WALT certified service center for a thorough cleaning, inspection and lubrication of the gear case.
Always use identical replacement parts. D E WALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www. This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others.
This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces. D E WALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase. If you are not completely satisfied with the performance of your D E WALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund — no questions asked.
Refer to Changing the Planer Knives section. Refer Dust Hood Installation paragraph in the Assembly section. Refer to Installing a New Belt paragraph in the Maintenance section. If the circuit breaker on your planer trips, check the sharpness of your knives before attempting to reset the breaker in order to continue planing.
Refer to Depth Adjustment paragraph in the Operation section. Ensure unit is plugged into the appropriate outlet, refer to the Important Safety Instructions for All Tools section. Refer to Figure 1 for proper location. Refer to Brushes paragraph under the Maintenance section. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password?
Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. See us on the World Wide Web at www. Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician.
The adapter C is not for use in Canada. Make sure switch is in off position before plugging in. The symbols and their definitions are as follows: V Class I Construction n o current Specifications Input Maximum 6" When transporting or storing the planer, use the cord wrap D located in the back of the tool Fig.
Bench Mounting To facilitate bench mounting, two different sized holes E are provided on the four corners of your planer as shown in Figure 4. NOTE: Tighten the bottom screw first and then the two side screws. Table Extensions Before using your planer, fold down the table extensions in the front and back of the tool Fig. Carriage Head Lock Your planer is equipped with a carriage head lock lever I located on top of the motor Fig.
Depth Adjustment The depth adjustment scale J indicates the finished thickness of your workpiece Fig. Raise head lock lever I to unlock the cutter head Fig. This allows the cutter head to be adjusted. Adjust the thickness. Turn the depth adjustment handle F clockwise to lower the cutter head.
Turn the handle counter-clockwise to raise the cutter head. Depress the head lock lever to re-lock before planing. You may damage the machine. Plane and measure your workpiece. Do not make any other adjustments to the planer. Plane your workpiece. The final thickness should be 3" D Material Removal Gauge Your planer is equipped with a material removal gauge. Never attempt recommended on the material to modify your planer to take a deeper cut.
Turret Stop 1. Lower the carriage to the desired height for your first Your planer is equipped with a F pass. Use the T-wrench to remove the eight screws on the knife clamp FIG. Use the magnets on the top of the T-wrench to attract the knife clamp and lift it off of the cutter head. WARNING: To reduce the risk of serious personal injury, However, with extended use, the depth adjustment scale could show turn tool off and disconnect tool from power source before an incorrect measurement.
Page 13 This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www. Page 14 This become illegible or are missing, call D WALT for a free warranty gives you specific legal rights and you may have other rights replacement. Page 26 5. Abaisser le levier de verrouillage R du porte-couteaux comme il 6. Bien resserrer les vis.
On risque ainsi de graves blessures. Gire el puerto hasta que se liberen los pernos de las ranuras del puerto. En con una empalmadora para producir una superficie plana. Si no todo momento, sostenga correctamente la tiene al menos una superficie plana ni una empalmadora, vea las pieza en la que trabaja.
Page 42 5. How can you fix or adjust planner when it doesnt want to raise up? Answer this question Send. About the DeWalt DW DeWalt DW specifications. Related product manuals. What is the weight of the DeWalt DW? The DeWalt DW has a weight of g. How do I remove rust from my DeWalt Planer? Soak the rusty part in vinegar until completely soaked through.
Let the vinegar work on the rust for 24 hours.
0コメント