Most likely, you'll need to cut a hole in the wall or floor in order to access the plumbing. Take out the old tub. First, unscrew the tub drain and overflow from the P-trap underneath the tub. If your tub is acrylic or fiberglass, cut it into pieces with a jigsaw to make the removal process easier. Use a utility knife to do so. Part 2. Select a tub that will fit in the designated space. Measure the length and width of the alcove where you will install the tub.
Also, measure the height and width of your bathroom doorway to make sure the tub will fit through the bathroom door! Take your measurements to a home improvement store to guide your purchase. Make sure your tub comes with all the faucets, drains, and accessories you will need. Dry-fit the tub in the alcove. To ensure the tub fits, place it in the designated area. Check that the drain hole in the bottom of the tub lines up with the P-trap in the floor underneath the tub.
Ensure you have the right fittings to connect the water supply lines to the faucet you purchased, as well. Use caution to prevent scratches or other damage to your new tub! Install a ledger board. Measure the height of the lip, or flange, of the tub, then mark that height measurement on the back wall. Use a drill to screw the ledger board to the studs in the wall so that the top of the ledger board is just below the flange when the tub is sitting level in the alcove.
Attach the drain to the tub. Before you actually set the tub in place, secure the drain to it. Place a gasket around the strainer from the outside of the bottom of the tub, then screw the strainer to the drain chute, which a long pipe that includes the overflow drain. Connect the overflow drain. Slip the trip lever stopper and linkage through the overflow drain opening on the inside of the tub. Use a screwdriver to secure the overflow cover with the trip lever to the inside of the tub.
The stopper and linkage go inside the pipe to stop or allow the flow of water. The overflow drain will prevent the tub from overflowing if you leave the water running as it directs the water into a drain pipe. Part 3. Set the tub in place and level it. Carefully position the tub in the alcove so that the drain rests over the drain opening in the floor.
Place a level on each side of the tub. If any spots are uneven, position hardwood shims underneath the tub and glue them in place. Secure the tub to the studs. There will be a small flange, or vertical lip, around the outside of the tub. In most cases, you can use a hammer to drive roofing nails through the flange to secure it to each stud in the wall. Fit a new tub surround.
The surround is made up of the panels that protect the wall around your tub from moisture and mildew. First, dry-fit the surround and mark the location of the accessories, including the faucet and water handles. Ensure that the faucet will line up with the water lines in the wall. Then, cut out the accessory openings with a jigsaw. A one-piece surround is the easiest type to install. Caulk the tub to the surround and secure the surround to the studs.
Place a bead of silicone caulk around the entire perimeter of the tub on the ledge next to the flange. Then, carefully set the surround on top of the silicone caulk.
Next, use a drill to screw the surround into each wall stud. Aim to use a screw every 6 inches 15 cm up the length of the surround. Connect the water lines and install your accessories. Screw the faucet into the coupling for the water lines through the hole in the surround. Then, screw the strainer cover over the drain opening in the floor of the tub. Add any other accessories you need, such as handles if they are separate from your faucet.
Connect the drain to the P-trap. Thread the drain chute into the P-trap under the tub. Caulk the tub to the floor. Run a bead of silicone caulk along the outside edge of the tub where it meets the floor. Make sure it meets both outside corners to prevent water from getting in between the tub and floor. Smooth out the bead with your finger or a damp rag.
Wait 24 hours before turning on the water. To give the caulk and other adhesives time to dry, wait at least a full day.
Then, you can turn on the water and check for leaks. If you find any problems, contact a certified plumber. Yes, I do, cement-board actually. Never use ANY drywall in any bath. View Pros. Table of Contents [hide] [show]. Get free estimates from tub pros near you.
Find the right bathroom remodeler for your project. Get started by hiring a plumber near you to install your jetted tub. Find a top-rated bathtub installer near you.
Wear eye protection and gloves for safety during the bathtub removal and installation. Still have questions? Ask a bathtub professional. Paxton, Albert S. PDF file. Thomson, James A. Hicks, Ray F. Russell, Jonathan. Pray, Richard. HomeGuide Survey. Bathtubs at The Home Depot. Personal Communication. Millions of people ask HomeGuide for cost estimates every year.
We track the estimates they get from local companies, then we share those prices with you. Related Articles. Bathtub Installation. Get Started. Bathtub Installation Near You. Looking for Bathtub Installers near you? How it Works. Bathtub Installation Near Me.
Replacing with same size and style tub Minor repairs and plumbing changes May preserve existing surround or tile. Your bathroom faucet is one of the most flexible and central pieces in the space. It is also very easy to replace when the current plumbing configuration supports the new model. Keep this hardware exchange simple by selecting a model that needs the same piping setup. For example, if you have a two-handle faucet, it is simplest to choose another two-handle set rather than convert to a centerset unit.
If you exchange one type for another, the project may become moderately difficult. A new shower head can reinvigorate your morning routine, increasing water pressure or making it easier to use. Like faucets, keeping the same configuration is key to keeping this a simple task.
Upgrading from a single to dual shower systems may require additional plumbing pipes depending on your current hot water capacity and preferred water pressure. Let experienced professionals reconfigure your plumbing, install the new product, and make your bathroom look like new again.
A soaking tub can round out your bathroom design. Elegant styles such as hammered copper or oversized models fit for two often require professional installation due to lifting and moving heavy objects and updating plumbing connections. Adding functional accessories like robe hooks, towel bars, and mirrors to your bathroom is easy.
Updating existing fixtures is simple, too, usually only needing a screwdriver, stud finder, and level. The hardest part might be deciding which style will best suit your bathroom decor. Barn doors are a popular, space-saving feature in contemporary and farmhouse style homes.
While this is not a difficult project, it can be tedious to measure and install perfectly.
0コメント